Roller Conveyors

Interroll Products

Straight RM 8110

The non-powered straight roller conveyor transports materials either manually or via gravity down a slope and is used as an assembly and picking line.

The Magnetic Speed Controller 50 can be installed for controlled speed regulation. These gearless, mechanical eddy current brakes reliably decelerate materials from 0.5 kg up to 35 kg, and increase functionality and safety in the workplace. For more information, please contact your Interroll contact person.

View details

Alignment Conveyor RM 8340

The 24 V alignment conveyor guides products diagonally to the transport direction to a side frame, and aligns them to the side guide if necessary. The side guide must be suitable for this purpose.

View details

Alignment Conveyor RM 8240

The alignment conveyor guides products diagonally to the transport direction to a side frame and aligns them to the side guide, if necessary. The side guide must be suitable for this purpose.

View details

Curve RM 8120

The non-powered roller conveyor curve changes the transport direction of materials. Material is manually pushed around the curve. The alignment of the material is maintained within the side frames by tapered rollers.

View details

Ball Table RM 8130

The ball table transports materials with a solid bottom in any direction using very little force. It is especially suitable for workstation & inspection areas. So that a ball table can be combined with other conveyors, it is installed in a standard side profile.

View details

Omni Wheel Table RM 8140

The omni wheel table with multi-directional wheels is particularly well suited for workstation and inspection areas and for materials with soft bottoms that can be moved in all directions with very little force.

View details

Straight RM 8310

The 24 V roller conveyor enables zero pressure accumulation transport of unit loads with the help of a controller. Each zone is powered by a RollerDrive that is connected to a fixed number of idlers via PolyVee belts.

View details

Curve RM 8320

The 24 V roller conveyor curves change the direction of transport of the material. The conical rollers retain the alignment of the materials between side frames. A controller enables zero pressure accumulation transport. Each zone is powered by a 24 V RollerDrive that is connected to a fixed number of idlers via round belts.

View details

Merge RM 8330

The merge merges two conveyor lines by placing products in the gaps in the material flow. Alternatively, the merge diverts products from a straight conveyor, e.g., by using an HPD (High Performance Divert).

View details

Straight RM 8210 / 8212

The roller conveyor powered by 400 V is available in 2 operating modes.

The permanently powered flat belt conveyor RM 8210 serves as a transport conveyor that requires only one 400-V drive for long distances up to 15 m.

With the use of electrical actuators, the conveyor can also be operated as zero pressure accumulation conveyor (RM 8212), either completely or partially. These actuators, which can also be retrofitted, are powered by 24-V drives and can be controlled by the Interroll controllers for zero pressure accumulation operation.

View details

Curve RM 8220

The roller conveyor curves change the direction of transport of the material. The alignment of the material is maintained within the side frames by tapered rollers. The flat belt-driven curve is driven either by an adjacent straight module or by a separate head drive. Accumulation mode is not possible in powered 400-V curves.

View details

Merge RM 8230

The merge is used for connecting lateral roller tracks at an angle (30° or 45°) to the main track. This can be used for moving material off the track (e.g. with HPD (High Performance Divert)) or onto the track.

View details

Heavy Conveyors & Components

The Interroll Heavy range offers handling solutions for thetransportation of heavy goods on Euro, GKN Chep or industry specific pallets with unit loads of up to 15000 N (1500kg)

using combinations of the following component parts:

  • Roller Conveyor Modules (Driven Or Non- Driven)

  • Transfer Car

  • Chain Transfer

  • Turntable

  • Combination of transfer cars and turntables

This allows system designers to concentrate on more important tasks such as system integration, layout planning, controls, installation and commissioning.

Examples of conveyed goods:

  • Euro Pallets

  • GKN Chep Pallets

  • Industry Specific Pallets

  • Heavy Products

Typical Applications:

  • Warehousing Systems

  • Distribution Centers

Features:

  • Individual modules can be easily combined

  • Simple installation of modules on site

  • Simple installation of sensors and control peripherals using profile T slots

  • Integral cable channels

  • Pre-assembled modules ready for use

  • Low maintenance

  • Low top of roller height

  • Proven Interroll quality rollers

  • Product guidance using roller mounted guide flanges

  • Modern aesthetic design

  • Robust construction

  • Drive: 3-phase, 400 V/50 Hz or 460 V/60 Hz

View details

Belt Conveyors

Interroll Products

Interroll Belt Curve

With a conveyor speed of more than 2 m/s, the Interroll belt curve is designed for high performance and trouble-free operation in different applications. The curves are available in several widths, angles and weight classes.

The Interroll belt curves can be operated in higher and lower temperature ranges, which represents a significant advantage compared to common solutions, such as friction-driven conveyors. Another advantage is the fast belt change. Thanks to the sophisticated construction, the drive station does not have to be removed for the belt change, thereby saving time.

View details

Inclined or Declined Belt Curve BM 4308 / 4312

Our Belt Curves 4308 or 4312 are available both as inclined or declined curves. Now it is possible to bridge a difference of levels. The basic design of this curve equals that of our curve type 4308 or 4312. The incline of the curve has been designed in a way that both the drive shaft and the deviating shaft remain in a horizontal position so that feeding-in and succeeding conveyors can be connected without any problems.

All indicated dimensions, esp. of the radii, equal the projected dimensions, as resulting from the top view. This is especially important for projecting systems.

View details

Straight BM 8350

The Belt Conveyor Light is a belt conveyor that is divided into zones and operates with zero pressure accumulation; its drive is based on the 24 V RollerDrive. It is possible to transport and accumulate small products, as well as products not suitable for roller tracks. Not suitable for reversing operation.

View details

Curve BM 8360

The Belt Curve Light is a belt curve that is divided into zones and operates with zero pressure accumulation; its drive is based on the 24 V RollerDrive. It is possible to transport and store small products, as well as products not suitable for roller tracks. Not suitable for reversing operation.

View details

Straight Head Drive BM 8410 / 8420

The belt conveyor is used for the transport of unit loads that are not suitable for roller tracks, and for all types of unit loads in case of inclines and declines.The standard belt conveyor is equipped with a drum motor (BM 8420), a gear motor is available as an option (BM 8410). Not suitable for reversing operation.

View details

Straight Center Drive BM 8411 / 8421

The belt conveyor is used for the transport of unit loads that are not suitable for roller tracks, and for all types of unit loads in case of inclines and declines.The standard belt conveyor is equipped with a drum motor (BM 8421), a gear motor is available as an option (BM 8411). Not suitable for reversing operation.

View details

Straight Center Drive + Top Arch BM 8432 / 8442

The belt conveyor with top arch is used for transporting all types of unit loads in case of inclines or declines. The arch reduces noise and the impact of materials as they pass over it.The standard belt conveyor is equipped with a drum motor (BM 8442), a gear motor is available as an option (BM 8432). Not suitable for reversing operation.

View details

Straight Center Drive + Feed BM 8433 / 8443

The belt conveyor with feed is used for transporting all types of unit loads in case of inclines or declines. The feed enables a smooth transition at the lower kink of the belt conveyor, e.g., at the interface with a roller conveyor.The standard belt conveyor is equipped with a drum motor (BM 8443), a gear motor is available as an option (BM 8433). Not suitable for reversing operation.

View details

Straight Center Drive + Top Arch + Feed BM 8434 / 8444

The belt conveyor is used for transporting all types of unit loads in case of inclines and declines. Arch and feed allow a smooth and quieter transition at the upper and lower kink.The standard belt conveyor is equipped with a drum motor (BM 8444), a gear motor is available as an option (BM 8434). Not suitable for reversing operation.

View details

Strip Belt Merge BM 4430 / 4445

The belt merge is a belt conveyor with a 30° or 45° angled connecting edge. This conveyor element enables the merging of two conveyor lines at the corresponding angle. With the use of supplementary sorting elements, belt merges also enable the separation of conveyor flows. The conveying belts are available in widths of 90 mm and 40 mm for especially small materials. The belt merge has an especially low overall height at 120 mm.

View details

Key Products

Interroll Products

RM 8711 Interroll High Performance Divert (HPD) 24 V Master

The High Performance Divert (HPD) is used for diverting unit loads, preferably with smooth bottom surfaces, at different angles onto a lateral track to the right or to the left. The HPD is available in two drive variants:

  • HPD 24-V master, for which 24-V motors are used as travel and swivel drives
  • HPD 400-V master, for which the travel drive from the flat belt conveyor is used, and the swivel drive is powered by a separate 24-V motor

One HPD module can consist of several cassettes, each 120 mm long, depending on the size of the product.

View details

Transfer RM 8731

The Transfer 24 V is used for diverting or merging onto a roller track suitable material at a 90° angle. In the process, the unit load changes direction and its orientation, i.e. the side of the product will now be the leading edge after the transfer.

View details

Lift-Up Gate RM 8830

The lift-up gate swivels upward to provide a walkway, or access from one side of the conveyor to the other. This allows access to the rear of the conveyor, and the ability to plan quicker escape routes, in case of an emergency. The pivoting movement is operated by an innovative rotary mechanism.

View details

End Stop RM 8811

The end stop is a permanently mounted attachment, for stopping and accumulating of approaching material. The end stop is used at the end of sloped or friction roller conveyors, or as a secure termination of all other conveyor lines.

View details

Blade stop RM 8812

The Interroll blade stop is an electrically operated stop that is raised between the roller pitches in order to stop or accumulate material. Stops are often used in conjunction with conveyor components, such as transfers and pushers, to align products or coordinate processes.

View details

Lift RM 6006

The lifting station consists of a column construction and a carriage upon which a roller conveyor is mounted. A worm gear motor with brake is used as a drive unit to raise and lower the carriage via a belt.

View details

Lift RM 6008

This vertical conveyor consists of a column construction and a carriage upon which conveyor components can be mounted. Lifting motion is performed by two toothed belts. The planned drive is located at the top. Integrating an encoder is possible. This lift can optionally be used at higher speeds and in several approach positions.

View details

Pusher ST 6110

The pusher pushes materials away at a 90° angle to the conveying direction. This is done gently despite high speeds, thanks to the electrically powered crank mechanism.

View details

Accessories

Interroll Products

Magnetic Speed Controller MSC 50

The Magnetic Speed Controller 50 is a purely mechanical speed controller that ensures a controlled, slow speed on gravity conveyors with materials weighing from 0.5 kg to a maximum of 35 kg. The magnetic speed controller operates without a gear box, thus enabling startup for very lightweight containers. Heavy containers are transported at a controlled speed thanks to the consistently high braking performance.

View details

Actuator

By using 24 V actuators, a 400 V roller conveyor can be operated as a zone conveyor. The actuators can be controlled for zero pressure accumulation mode via the Interroll controllers. Additional components are required to change a transport conveyor into a zone conveyor. Please contact your Interroll customer representative.

View details

Sorters

Interroll Products

Interroll Horizontal Crossbelt Sorter

Horizontal crossbelt sorters are characterized by their flexible, space-utilizing routing with curves that also conquer inclines and slopes. Feeds and destinations can be arranged in various ways and optimized to increase the system's performance. With an appropriate layout, it is possible to create several sorting areas with just one cycle. The horizontal crossbelt sorter is also perfectly suited for small spaces. For example, two crossbelt sorters with identical routes can be installed one on top of the other, i.e., doubled up. Horizontal crossbelt sorters can recirculate goods that have either not been recognized by identification technology or have not been discharged because all destinations were full.

View details

Interroll Vertical crossbelt sorter

The main feature of Interroll's vertical crossbelt sorter with linear, straight routing ("above – below") is its distinctive space-saving design because of its compact, modular approach. A minimum width of 1.7 m is already sufficient, e.g., for a vertical sorter with a crossbelt carriage measuring 400 x 400 mm. This configuration can also save valuable space, if full containers are transported into the sorter. This is unique on the market. The infeed on the vertical sorter usually starts with an accumulating conveyor in front of the actual sorter - a simple conveyor belt. Operators are able to manually feed goods directly onto this accumulating conveyor - a cost-effective and ergonomic solution. The accumulating conveyor can, of course, also be loaded via semi-automated or fully-automated infeeds.

View details

RM 8711 Interroll High Performance Divert (HPD) 24 V Master

The High Performance Divert (HPD) is used for diverting unit loads, preferably with smooth bottom surfaces, at different angles onto a lateral track to the right or to the left. The HPD is available in two drive variants:

  • HPD 24-V master, for which 24-V motors are used as travel and swivel drives
  • HPD 400-V master, for which the travel drive from the flat belt conveyor is used, and the swivel drive is powered by a separate 24-V motor

One HPD module can consist of several cassettes, each 120 mm long, depending on the size of the product.

View details

Transfer RM 8731

The Transfer 24 V is used for diverting or merging onto a roller track suitable material at a 90° angle. In the process, the unit load changes direction and its orientation, i.e. the side of the product will now be the leading edge after the transfer.

View details